Home > Metal Moulding Machinery >

14DH Intermediate - Fine Wire Drawing Machine With Large Spool Pneumatic Brakes

Categories Customized Wire Drawing Machine
Brand Name: HXE
Model Number: 14DH
Certification: ISO/SGS
Place of Origin: China(Mainland)
MOQ: 1 set
Price: Negotiable
Payment Terms: T/T, L/C
Supply Ability: 40 sets per year
Delivery Time: 45-60 work days
Packaging Details: Packed with plastic film, U-steel under the machine
Usage: Drawing
Inlet diameter: ф1.6mm/max
Outlet diameter: ф0.25-ф0.65mm
Max line speed: 800MPM/MAX
Main motor: AC15.5KW motor
Take-up motor: AC7.5KW motor
Product name: Non standard wire drawing machine
After-sale service: Engineer available to overseas
  • Product Details
  • Company Profile

14DH Intermediate - Fine Wire Drawing Machine With Large Spool Pneumatic Brakes

HXE-14DH Copper wire drawing machine with large spool

I. Machine overview
This machine adopts programmable controller and dual inverters, the sliding and automatic speed control and variable speed. With energy Low consumption, high reliability, small slip rate, long life, large capacity of take-up, low noise, nice shape, etc.Machine is operation simply, safe, reliable, and easy maintenance. In order to make the user familiar with and master the rules, please users read this manual carefully before using.

II. Components

1. Pay-off stands1 set
2. HXE-14DS Drawing machine1 set
3. Spare parts

III. Parameters
(1) Inlet : ф1.6mm/max copper; ф2.5mm/max aluminum
(2) Outlet: ф0.25-ф0.65mm; ф0.4-ф0.8mm
(3) Mechanical speed: 800MPM/MAX
(4) Dies: 14 (buyer-owned) Max
Dies: 7 (buyer-owned) Minimum
(5) Dies OD: ф25mm X 8 - 12mm thick
(6) Slip ratio: 1 -13, 15%;14, 8%
(7) Main motor: AC15.5KW motor
(8) Take-up motor: AC7.5KW motor
(9) Take-up diameter: ф400 - ф500
(10) brake: pneumatic brakes
(11) Power consumption:15-30kw power
(12) Lubrication capacity: 150L/MIN

IV. Note

1. to achieve the requirements of this specification, the cable must be reasonable, good Lubricating fluid, good Dies, and high-quality copper wire.
2. not used the reel without balancing requirement.
Electrical system normal conditions are as follows:
A. Environmental temperature: -10 ℃ ∽ +40 ℃ (no freezing conditions), a 24-hour period, the average temperature does not exceed +35 ℃.
B. atmospheric conditions: air, harmless dust, corrosive and explosive gases.
C. Relative humidity: +40 ℃ when the maximum temperature does not exceed 50%, a lower temperature allows a higher relative humidity of 85% at +20 ℃.
D. Altitude: not more than 1000M, more than 1000M, specified in accordance with this.


Correction facto
E. Power supply voltage: sinusoidal, three-phase four-wire 380V, 50HZ; voltage fluctuation range does not exceed the rating of ± 5%, should ensure that output ratings; voltage fluctuations not exceeding ± 10%, should ensure reliable operation ; frequency fluctuations should not exceed the rating of ± 2%.
F. Install inclination: Vertical mounting installation inclination should not exceed 5%.

V. Preparation before working

5-1. Check all parts lubrication conditions,
5-2. Check drawing lubrication oil, cooling water, steam, air pressure.
5-3. After checking, connect to power, according to the Electrical drawing, use foot switch, to make the machine operating in low speed (under 4m/s), if no Abnormal, then can begin to work.

VI. Operating procedures

6-1. Open power switch
6-2. According to the wire diameter, choose the dies (Check the die list).
6-3. Use pliers to break the wire to get a smaller section.
6-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).
6-5. Wire direction, please check the Drawing for Wire path.
6-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.
6-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.
6-8. Set the length meters, then press the Start button to start the machine.

Cheap 14DH Intermediate - Fine Wire Drawing Machine With Large Spool Pneumatic Brakes for sale
Send your message to this supplier
*To: Suzhou Hengxie Machinery Co., Ltd
Characters Remaining: (0/3000)
You may also be interested in :
Inquiry Cart 0
  • Haven't found right suppliers
  • Our buyer assistants can help you find the most suitable, 100% reliable suppliers from China.
  • And this service is free of charge.
  • we have buyer assistants who speak English, French, Spanish......and we are ready to help you anytime!
  • Submit Buying Request
    Contact Us Quickly