Original Tango Car Key Programer With Basic Software
After generating a new transponder with TANGO Programmer, you will
not need any additional diagnostic equipment to program the
generated transponder to the car! It will start the car directly,
even on new FIAT CODE 2 system, also used in PSA Group vehicles!
Only you have to write the new file back into the immobilizer
Tango Software V1.80, Tango Software Added:
Key maker Chevrolet Cruze 2008- (24C16,HITAG)
Key maker Chevrolet Lacetti 2005- (ST7,ID4D)
Key maker Renault Mascott 2002- (93C66,HITAG)
Key maker Renault Clio II 2003- (93C66,HITAG)
Key maker Hyundai Accent 2004- (93C56,ID4D)
Key maker Hyundai H1 2001- (93C56,ID4D)
Key maker Hyundai H200 2001- (93C56,ID4D)
Key maker Hyundai Santa Fe 2006- (93C56,ID4D)
Key maker Hyundai Sonata 2003- (93C56,ID4D)
Key maker Hyundai Starex 2002- (93C56,ID4D)
Key maker Hyundai Terracan 2001- (93C56,ID4D)
Key maker Hyundai Trajet 2004- (93C56,ID4D)
Key maker Kia Carnival 2002- (93C56,ID4D)
Key maker Kia Sorento 2003- (93C56,ID4D)
Key maker Volvo V40 2004- (9S12,ID48)
Key maker Volvo V50 2004- (9S12,ID48)
New pictures in help file (total 315MB)
Tango Software V1.79:
Key maker Honda Stream -2006 (93C46,ID48)
Key maker Honda Fit 2007- (93C66,HITAG)
Key maker Honda bike ECU 38770-KTW-901 (93C66,HITAG)*
Key maker Honda bike ECU 38770-MCZ-003 (93C56,HITAG)*
Key maker Honda bike ECU 38770-MFN-D01 (93C56,HITAG)*
Key maker Honda bike ECU 38770-MEE-702 (93C56,HITAG)*
Key maker UAZ Hunter (TC1762,HITAG)
Key maker Suzuki SX4 2012- (TC1762,HITAG)
Key maker Mazda B3000 2001- (95040,ID4D)
Key maker Ford Focus 2000 (77012,ID4D)
Key maker Ford Ka 2007 (93C86,ID4C)
Key maker Chrysler Voyager Limited 2008- (93C86,HITAG)
Calculator Techstream 96 digits*
New pictures in help file (total 304MB)
List of Supported Transponders:
PCF7930-31 writing, reading
PCF7935 writing, reading, shadow memory, crypto calculator
PCF7936 writing, reading, modes password, crypto, Manchester &
PCF7941 transponder, remote, eeprom, Manchester & Biphase
PCF7942 transponder, remote, eeprom, Manchester & Biphase
PCF7943 transponder, remote, Manchester & Biphase encodings
PCF7944 transponder, remote, eeprom, Manchester & Biphase
PCF7945 transponder, remote, eeprom, Manchester & Biphase
PCF7946 transponder, remote, Manchester & Biphase encodings
PCF7947 transponder, remote, eeprom, Manchester & Biphase
PCF7952 transponder, remote, eeprom, Manchester & Biphase
PCF7961 transponder, remote, Manchester & Biphase encodings
Auto switching between PCF7936-PCF7961 windows if invalid type
Autodetect manchester / biphase
Temic 11 reading , writing to T5
Temic 12 reading , writing to T5
Megamos (13) reading , writing to T5 , emulating on PCF7930-35
Megamos (48) reading, writing, PIN, unlock by PIN, full range of
memory contents, crypto calculation
Megamos CRYPTO-2 (8E) read ID, read/write EEPROM, write Cryptokey
Tiris (4C) reading
Tiris (4D) DST crypto reading, writing, crypto calculator
Tiris (4E) DST crypto reading, writing, crypto calculator
Tiris (8C) reading
TK5551M (T5 replacement)
SAAB reading , writing to T5
The product is in working out stages, therefore the list of the
supported transponders will be developed later.
Key Maker Usage.
Key maker usage consists of a four steps. The 4-th step is
additional and depends on a vehicle model.
1. Open an immobilizer dump file.
2. Choose number of the key you want create.
3. Place a transponder into the coil and click the WRITE button.
4. In some cases the program asks you to save a modified
immobilizer dump. This dump must to be written into the
First of all, take a look at this picture. The "Loaded File" window
displays the immobilizer file name. Ensure that a valid dump is
stored. The "Maker" window displays selected maker name. Ensure the
right key maker selected.
The "info" windows display an important information:
1. Original transponder---Informs you about type of the original
2. Allowed transponder---Informs you what type of transponders is
suitable for the key maker
3. Data location---The immobilizer memory may be stored in various
chips, the description informs you about from where you have to
read a dump. Some immobilizers can have various chipsets. In this
case the field displays several possible chips. Find one of them
inside of the immobilizer and read it.
4. Data size---Each chip has certain memory size, the key maker
accepts files with the described size.
5. Data format---This field appears in case of 93CXX eeprom seria.
There are two standards of data layout:
Intel format and Motorola format or Little Endian and Big Endian
The data layout depends on a chip-programmer that is used for
eeprom reading.This field informs you what kind of format is
suitable for the key maker.Usually you can see that both formats
are suitable. It means that the program can understand any data
Create a Key Step by Step
Firstly, run the key maker interface according to the vehicle and
read information in the "Info" window. Watch theData location field
describes the memory chip. Find out the chip inside of the
immobilizer and read it. Save the read data (dump).
Click the "OPEN IMMOBILIZER FILE" button and load the saved dump.
The program will analyse the dump.
If the dump is correct the "WRITE" button will become active and
the "Keys" window will display the range of key numbers that can be
Take a look at the "Info" window, the Allowed transponder field.
Ensure you use a transponder exactly the indicated type.
Place the transponder into the coil.
Choose the key position you want create in the "Keys" window.
Click the "WRITE" button.
This starts the writing process and transponder will be stored with
the appropriate data.
At this point you may be asked to save a new immobilizer dump.
The program displays a standard File Save dialog where you have to
save the data.
After this you will be informed about the new data saved and must
be written into the immobiliser.
Write the new dump into the immobilizer. Now it is ready to operate
with the created transponder.If you are not asked to save a new
file, it means that immobilizer is ready to operate with the
created transponder without file replacing.
1. ABS plastic enclosure: ingress protection IP65/DIN EN 60529
2. Rubber seal: prevents sliding on a workbench shock-proof
3. USB connection: no external power
4. Big hole: adopted to large keys
5. Three small holes: adopted to various sizes of transponders