Sign In | Join Free | My fazendomedia.com
China Wuxi Yijiaer Tech Group limited logo
Wuxi Yijiaer Tech Group limited
ICP Remarked Supplier
Home >

Press Accessories Press Plate

Wuxi Yijiaer Tech Group limited

Press Accessories Press Plate

Country/Region china

Company Wuxi Yijiaer Tech Group limited

Categories Mounting Press

Update 2018-12-07 08:36:11

ICP License Issued by the Chinese Ministry

Contact Now

Product Description

Stainless steel press plate installation, pretreatment and use

1. The new press template used for the first time should be cleaned with a clean gauze, washed with hot water diluted detergent, washed, wiped, and dried. When installing, follow the first step on the cushion. Put on the template, then lay down the cushion, install the order of the template. There are four things to note in the installation:

1). There is a card type slot on the hanging Gui device to facilitate the adjustment of the position of the template. So as to maintain the shape and flatness of the template;

2). The cushion must be laid flat without deformation;

3). Avoid falling into lubricants and debris during the installation process;

4). If using a tensioning device, consider the expansion factor.

2. In order to achieve a complete surface effect of the product, after many years of research and experiments, the design and manufacturing staff of our company proposed that due to the different performances, pressures, and veneer processes of the press, the newly used template must be pre-adapted for adaptability. deal with. After verification, good results have been achieved. Template preprocessing steps:

A. When the template is used, the surface is coated with a release agent or special silicone oil (our company has a special template mold release agent). Under repeated temperature changes, the release agent penetrates through the capillary pores of the template to form a A delicate and sturdy mucous membrane.

B. Spread 1-2 layers of white paper on the working surface of the template, and sandwich 2-4 layers of kraft paper in the middle. Note that unimpregnated base paper is used for the above papers to avoid soiling the surface of the stencil with a resin that is under no pressure.

3. Close the hot press, gradually increase the temperature without pressure, 30 °C - 60 °C - 90 °C - 60 °C - 120 °C - 150 °C until the maximum hot pressing temperature. Repeatedly back and forth more than 20 minutes. Then it is naturally cooled, pressurized to 20-30 Kg/cm3, and finally the hot press is turned on so that the surface structure of the template is maintained and smoothed under repeated temperature changes.

As a result, a large number of pressing processes can be tolerated in the production process and the surface finish and gloss of the stencil surface do not change. Extend the service life of the template.

4. Our company recommends that users who produce laminate flooring and melamine panels use special chrome-plated stencils with high hardness and good durability, because the laminate flooring will directly wear melamine surface materials in a short time press (with Decorative paper with aluminum oxide or transparent surface paper is made by hot pressing and affixing to the surface of a wood-based panel. Therefore, the special chrome plated stencil has the property of reducing friction of aluminum oxide and prolonging the service life of the stencil.

Press Plate Storage, Maintenance and Repair

1. Spare or template for long-term storage, wipe the plate with acetone, then apply a layer of release agent evenly on each piece, and stack them neatly in a horizontal manner. And cover the velvet to prevent dust. As far as possible, it should be distributed in a well-ventilated place, especially electroplating stencils. If it is placed in a humid place, the surface of the electroplating layer is likely to come into contact with acidic or alkaline substances in the air, causing moldy spots and affecting the gloss of the stencil.

2. The use of soft light board in addition to the above requirements in addition to the acetone solution in the same direction lightly, can not be used to force rub.

3. In the production process, the plywood has been found to have sticking phenomenon (remove the plate more difficult), the template should be promptly removed, soaked in boiling water to soften the curing glue residue, and then wash with detergent, well coated Professional release agent.

4. Even if the press template is used normally, our company still advises the user to clean the template regularly (a month or two months depending on the output) and apply a special release agent to ensure that no sticking occurs. Once the glued board cannot use the metal tool to remove the veneer, this will damage the template. The only feasible way is to take the template together with the veneer, soak it in hot water for dozens of hours, slowly let the veneer Separate and then use wooden tools to clean up the remaining swarf.

5. Replace the template to be maintained, and clean the resin smudges and residual pieces accumulated on the template in time. When cleaning, the template should be placed on the workbench (high-pressure template should be laid on the surface of t


Product Tags:

gift wrapping paper

      

mold release agent

      

stainless steel

      
China Press Accessories Press Plate

Press Accessories Press Plate Images

Inquiry Cart 0
Send your message to this supplier
 
*From:
*To: Wuxi Yijiaer Tech Group limited
*Subject:
*Message:
Characters Remaining: (0/3000)